TEST REPORT
No.  : SHIN1702006091MR-01
Date : Mar 14, 2017
Page:    1 of  11
CUSTOMER NAME: SHANGHAI XINFAN INDUSTRIAL CORPORATION
ADDRESS: NO.1336, JINGE ROAD, JINSHAN DISTRICT, SHANGHAI, 201506
CHINA
This Report cancels and supersedes the Report No.: SHIN170206091MR dated: Feb 21  ,2017 issued by SGS-CSTC Standards Technical Services (Shanghai) Co.,Ltd, original report will be invalid from today.
Sample Name : Bolt Seals
Product Specification : NEW TSS-BS02
Manufacturer : Shanghai Xinfan Industrial Corporation
Other Information : IN-SH-5802-17042
Above information and sample(s) was/were submitted and confirmed by the client. SGS, however, assumes no responsibility to verify the accuracy, adequacy and completeness of the sample information provided by client.
***********
SGS Ref. No. : SHIN1702006044PS
Date of Receipt  : Feb 13, 2017
Testing Start Date  : Feb 13, 2017
Testing End Date : Feb 21, 2017
Test result(s)    : For further details, please refer to the following page(s)
(Unless otherwise stated the results shown in this test report refer only to
the sample(s) tested)
Signed for
SGS-CSTC Standards Technical
Services （Shanghai）Co., Ltd.
Authorized signatory
TEST REPORT
No.  : SHIN1702006091MR-01
Date : Mar 14, 2017
Page:    2 of  11
Summary of Results:
No. Test Item  Test Method Result Conclusion
1 Impact test ISO 17712:2013 section 5.5 See result  /
2 Shear test ISO 17712:201
3 section 5.3 8896 N  /
3 Tensile Test ISO 17712:2013 section 5.2 20.7 kN  /
4 Bending Test
(Rigid seals)
ISO 17712:2013 section 5.4 59.04 Nm  /
Pass : Meet the requirements;
Fail : Does not meet the requirements;
Note:
/ : Not Apply to the judgment.
TEST REPORT
No.  : SHIN1702006091MR-01
Date : Mar 14, 2017
Page:    3 of  11
1. Test Item:  Impact Test
Sample Description: Bolt Seal
Test Method: ISO 17712:2013 Section 5.5
Test Condition:
Dead blow weight: 4±0.01kg
High Temperature: 18℃
Low Temperature: -27℃
Lab Environmental Condition: 23±2℃, 50±5%RH
Test Result:
Test Item    1    2    3    4    5 High Temperature
Impact Load, J
＞ 40.68 ＞ 40.68 ＞ 40.68 ＞ 40.68 ＞ 40.68 Low Temperature
Impact Load, J
＞ 40.68 ＞ 40.68 ＞ 40.68 ＞ 40.68 ＞ 40.68 Seal Classification H
Impact test seal classification requirements
Low Temperature Impact Load, J High Temperature
Impact Load, J
Dead Blow Mass Drop
Height
Seal Classification
40.68 40.68    1.037 m “H” (high-security seal) 27.12 27.12 0.691 m “S” (security seal) <27.12 <27.12 0.346 m “I” (indicative seal)
TEST REPORT
No.  : SHIN1702006091MR-01
Date : Mar 14, 2017
Page:    4 of  11
Test Photo:
During test- at Low temperature
During test- at RT Before test
TEST REPORTsgs报告
No.  : SHIN1702006091MR-01
Date : Mar 14, 2017
Page:    5 of  11
After test- at RT After test- at Low Temperature
Equipment Information:
Equipment Model Equipment No. Calibration date Next Calibration date Tensile impact
/ P-368 2016-6-28 2017-6-27 tester
Damp heat
KAHA-480KBS P-129 2016-7-22 2017-7-21 chamber